PSA
StationArena

Solar · BLUETTI

Solar panels for the BLUETTI Elite 30 V2

Written by Ian Schneider·Solar & Off-Grid Tester

BLUETTI rates the Elite 30 V2's solar input at 200 W, 12 to 28 volts, through a single XT60 socket. Twenty-two of the forty-one panels we track read above 28 volts on the label, four of them BLUETTI's own. The manual prints the ceiling twice, once in the spec table and once on the warning page, and the warning page keeps it short: no panels above 28.

Thirteen stay under, and none of them fills a 200 W port on its own. One 200 W folding panel delivers about 144 W in real sun, and 288 Wh at that rate is about two hours. Two of BLUETTI's own PV200 panels bring the port up to its full 200 W, and the battery is done in a little under an hour and a half. For a weekend at the cabin I'd carry one PV200 and give it the two hours. The second panel is for people in a hurry, and I am not in a hurry at the cabin.

The door
12–28 V
Its width
200 W
Plug
XT60
Full battery, best case
~1.4 h
BLUETTI Elite 30 V2 portable power station
Plug in the wall charger while a panel is connected and the manual caps the two together at 380 W. The panel is the side that gives.

The door

Every panel we track, lined up at the Elite 30 V2's solar input

Every panel we track, in a line by the voltage on its label. That figure is the open-circuit voltage, Voc on the sticker, the voltage a panel makes in sun with nothing plugged into it. The black line sits at 28 V, where BLUETTI's manual draws its own. Twenty-two bars stand over it.

The pale cap on each bar is what a −10 °C morning adds, about 10%. Five panels clear 28 only with the cap on. EcoFlow's 45W and 60W both read 25.6 V on the label and are two of the five. A panel reads one thing on a mild afternoon and another at sunrise on my deck in January. I'd have my Fluke meter on it before the plug went anywhere near the socket.

Hover a bar and it names the panel. If you already own one, type its Voc into the field below and it takes a place in the line.

Swipe sideways for the whole line-up.

010203040506070volts, open-circuit+1++2yours?28 V · the lintel12 V · the step

Hover or tap a bar for the panel’s name and its verdict.

  • Fits through the door
  • Too tall
  • Extra height on a −10 °C morning
  • Maker prints only the operating voltage; the real height is above the dashes
  • 1Our pick: BLUETTI PV200
  • 2BLUETTI's own SORA 500

What we'd buy

The best solar panel for the Elite 30 V2

Picked by the numbers on this station, not by brand.

Best overall

200 W
BLUETTI PV200 (200W Solar Panel)

2 panels deliver 200 W, the most the input takes.

Best value

Renogy 100W N-Type Lightweight Portable Solar Panel Suitcase (COMPACT-SUITCASE 100 / RSP100LSC)

About $2.33 for every watt it actually delivers here. 3 panels deliver 187 W.

Check price at Renogy

Best to carry

Renogy 200W Portable Solar Panel Blanket (RPP200SB-SE)

144 W from a 8.82 lb panel, the most delivered watts per pound.

Check price at Renogy

A day on solar

How long the Elite 30 V2 takes to charge on solar

The strip below is a day of sun with a tick at the hour the battery is full. With the input full at 200 W the tick lands at 1.4 hours. Three sets we track get it there: two PV200s, two of Eco-Worthy's 195 W rigid panels, or three SP100Ls. One 200 W panel alone gives about 144 W and takes about two hours. One 100 W panel gives about 72 W and takes about four.

A good day has three to six hours of sun that strong. Even one 100 W panel finishes inside a good day. The 200 W sets are done by mid-morning and spend the afternoon with nothing to do. The system builder counts how many days like that your state gets in a given month.

a good day's sun: 3 to 6 h0 h1 h2 h3 h4 h5 h6 hInput full (200 W) · full in 1.4 hOne 200 W panel (144 W delivered) · full in 2 hOne 100 W panel (72 W delivered) · full in 4 h

Hours of good sun, from empty. Where you live and the month decide how many of those a day gives; the system builder works it out.

Every panel that fits

Solar panels compatible with the Elite 30 V2

Thirteen fit. For each: the cable that reaches the XT60 socket, what one panel delivers in good sun, and the most the Elite 30 V2 will take from a set. Nothing in the box connects any of them. The manual's FAQ asks for a panel with MC4 connectors, the weatherproof click-together plugs on most panels, and the product page names the station's end as XT60. BLUETTI's solar charging cable bridges the two and is sold separately. The 200 W panels want a second alongside, wired in parallel, plus to plus and minus to minus, so the current adds and the voltage does not. The 100 W panels want two more. Sorted by delivered watts.

Too tall

Solar panels that won't work with the Elite 30 V2

Twenty-two panels read over 28 volts. Four are BLUETTI's own. The PV100 FX, the 350W and the SORA 500 are over outright, at 41.4, 44 and 49.1 V, and were built for the brand's bigger stations, where they belong. Inside the Elite 30 V2 a charge controller stands between the panel and the cells, and BLUETTI rated it to 28 V. The SORA 500 would hand it 49.1. That leaves the PV200 and the SP100L as the BLUETTI panels this BLUETTI station will take.

Five of the twenty-two cross only on a cold morning. The SORA 60 is one, at 27.5 V on the label. EcoFlow's 45W and 60W both read 25.6 V. The Jackery SolarSaga 40 Air reads 26, and Jackery allows 5% either way before the cold adds about 10% on top. On a mild afternoon any of them would probably settle under 28. The mornings I plug panels in at the cabin are not mild, and I wouldn't spend a $279.99 station finding out where 25.6 ends up at sunrise.

Over the 28 V lintel (22)

No verdict (6): the maker doesn't publish an open-circuit voltage

Own a panel that isn't in the line-up?

Type its voltage into the door chart above for the height test, then put the rest of the label into the panel checker, already set to the Elite 30 V2, for current and plug too. Or build the whole system to see how it keeps up where you live.

The plain answers

How long does the Elite 30 V2 take to charge on solar?

One 100 W panel delivers about 72 W in good sun and refills the 288 Wh battery from empty in about 4 hours.

One 200 W panel delivers about 144 W in good sun and refills the 288 Wh battery from empty in about 2 hours.

At its 200 W solar limit it refills in about 1.4 hours. More panel watts than that won't charge it any faster.

A day gives three to six hours of sun that good, depending on season and place, so one 100 W panel takes 1 to 2 days to fill it. The system builder works it out for your state and month.

What adapter does the Elite 30 V2 need for solar?

Every panel we track needs a cable to reach its XT60 input. None comes in the box.

The cables they need: MC4 to XT60 (6 panels), DC8020 to XT60 (1 panel) and Anderson to XT60 (1 panel).

5 panels don't have a named plug from their maker, so check the lead before you buy a cable.

Can you use non-BLUETTI solar panels with the Elite 30 V2?

Yes. What decides it is the panel's voltage and plug, not the brand. 11 panels from EcoFlow, Jackery, Renogy, Rich Solar and Eco-Worthy work with it, as long as the panel stays under 28 V on a cold morning and starts above 12 V.

The strongest single panels here are the EcoFlow NextGen 220W Bifacial Portable (158 W delivered) and the Jackery SolarSaga 200W (144 W delivered).

Can you connect two solar panels to the Elite 30 V2?

Yes, joined into one input with a series or parallel cable.

Don't wire two BLUETTI SP100L panels in series: together they would pass its 28 V limit. Parallel them instead.

Past 200 W delivered, more panels only help on cloudy days.

What is the Elite 30 V2's solar input?

DC Input: 12–28 V, up to 10 A, 200 W.

Input limits from BLUETTI's documents, checked 2026-09-18 (source). Delivered watts assume 72% of the panel's rating in good sun.